+ | ikego

Ikego Parts 4

by Lars2i / ago

Parts we suggested for/added to the Trikka parts catalog.

–

1 Rod 210mm ⌀ 16mm

via KRH 12

doku schon da

Part info

  • What: Off the shelf rod
  • material: strong
  • measures: ⌀ 16 mm, length ~210mm

Tolerance

Get the part

  • Buy: Readily available in stores, search for: “rod 16mm” or something similar. | Also available as local make.
  • Make: Just shop a rod and cut it to the correct length.

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

2 Disk ⌀ ~120mm

via KRH 12

Part info

  • Disk
  • material: strong
  • measures: ⌀ ~120mm, thickness ~16mm
  • holes: Trikka grid, center hole ⌀ 16mm, the other four ⌀ 10mm, It is two lines with holes the cross in the center hole (16mm) at 90° to each other

Tolerance

Get the part

  • Buy: Only as local make.
  • Make: No instructions available.

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

3 rubber band 150mm

via KRH 12

Part info

  • Off the shelf rubber or silicone band
  • material: bendable
  • measures: ~ 150mm (if you would cut it open)

Tolerance

Get the part

  • Buy: Readily available in stores, search for: “rubber band” or “silicone band”
  • Make: No instructions available.

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

4 Set collar with ⌀ 16mm hole

via KRH 12

Part info

  • A set collar
  • material: strong
  • measures: outer ⌀ ~32mm, thickness ~16mm
  • holes: a large center hole ⌀ 16mm, a hole on the set for the Locking bolt ⌀ 4mm. For more details download the part file below.

Tolerance

Get the part

  • Buy: Only as local make.
  • Make: The part you see in the picture is made with a laser cutter. We cut 10mm acrylic (8mm also works) and then drilled the small hole from the side using a cordless screwdriver. If you draw this yourself make sure you have measures for the hole for the M4 nut right (3,2x7mm) – the trick is that the nut is held by the shape of the part. A wrench is not necessary. →  DOWNLOAD LASER FILES. One last hint: Acrylic seems stronger than it is. A component made of acrylic should not be subjected to too much stress. Even thick acrylic breaks quickly. If you get the chance to use other materials for this part (like 3d printing or recycled plastic) great.

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

5 Set collar rail ⌀ 16mm hole

via Lift Lamp

Part info

  • A set collar rail
  • material: strong
  • measures: outer ⌀ ~32mm, thickness ~16mm
  • holes: a large center hole ⌀ 16mm, a hole on the set for the Locking bolt ⌀ 4mm. The smaller hole next to the large one is ⌀ 10mm. The spacing between the centers of the two large holes is 30mm (Trikka grid). For more info download the files below.

Tolerance

Get the part

  • Buy: Only as local make.
  • Make: The part you see in the picture is made with a laser cutter. We cut 10mm acrylic (8mm also works) and then drilled the small hole from the side using a cordless screwdriver. If you draw this yourself make sure you have measures for the hole for the M4 nut right (3,2x7mm) – the trick is that the nut is held by the shape of the part. A wrench is not necessary. →  DOWNLOAD LASER FILES. One last hint: Acrylic seems stronger than it is. A component made of acrylic should not be subjected to too much stress. Even thick acrylic breaks quickly. If you get the chance to use other materials for this part (like 3d printing or recycled plastic) great.

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

6 M4 hook

via Hanger One

Part info

  • Off the shelf M4 hook
  • material: strong
  • measures: ⌀ 12mm, thread length 20mm, overall length 40mm

Tolerance

Get the part

  • Buy: Readily available in stores, search for: “M4 hook” and check the measures above.
  • Make: No instructions available.

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

7 headphone circle part 1

Via Trikka Headphones

Part info

  • disk
  • material: strong
  • measures: Outer ⌀ ~75mm, thickness ~16mm
  • holes: Trikka grid, 5 holes ⌀ 6mm (for more info download vector files below)

Tolerance

Get the part

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

8 headphone circle part 2

Via Trikka Headphones

Part info

  • disk
  • material: strong
  • measures: Outer ⌀ ~75mm, thickness ~16mm
  • holes: Trikka grid, 5 holes ⌀ 6mm (for more info download vector files below), the smaller holes are ⌀ 2 mm and 10mm away from each other

Tolerance

Get the part

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

9 Strap 300mm, 10 holes

Via Flower hanger

Part info

  • A strap
  • material: bendable but strong
  • measures: ~ 300 mm x ~ 30 mm x
  • holes: Trikka grid, 5mm holes

Tolerance

Get the part

  • Buy: Only as local make.
  • Make: This is easy to make. We recommend PP (Polypropylen) 0,8 mm or 1 mm  for it. PP can be cut by hand but you can also use a laser cutter. For this we share laser-cut-ready files: DOWNLOAD svg files

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

10 M4 wing nut

Via Lift Lamp

Part info

  • Off the shelf M4 wing nut
  • material: strong

Tolerance

Get the part

  • Buy: Readily available in stores, search for: “M4 wing nut”
  • Make: No instructions available.

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

added as part 044.1

11 strap 3 holes

via Lift Lamp

Part info

  • Strap
  • material: bendable but strong
  • measures: ~ 90 mm x ~ 30 mm
  • holes: Trikka grid, 3 holes ⌀ 4 mm

Tolerance

Get the part

  • Buy: Only as local make.
  • Make: This is easy to make. We recommend PP (Polypropylen) 0,8 mm or 1 mm  for it. PP can be cut by hand but you can also use a laser cutter. For this we share laser-cut-ready files:  DOWNLOAD svg files

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

12 M4 bolt 4-9mm

via Flower Hanger

Part info

  • Off the shelf M4 bolt
  • material: strong
  • measures: thread 4 mm to 9 mm

Tolerance

  • Size: thread ISO/DIN 13. But if you have nuts and bolts from a different standard with a diameter of 4mm it should work in most applications. Bolt head type not specified. Use what you like.
  • Material: standard tolerance

Get the part

  • Buy: Readily available in stores, search for: “M4 bolt”
  • Make: No instructions available

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

13 M4 nut

via Flower Hanger

Part info

  • Off the shelf M4 nut
  • material: strong

Tolerance

  • Size: thread ISO/DIN 13. But if you have nuts and bolts from a different standard with a diameter of 4mm it should work in most applications.
  • Material: standard tolerance

Get the part

  • Buy: Readily available in stores, search for: “–” | Only as local make.
  • Make: No instructions available.

Introduced by

  • Designer: Lars Zimmermann via
  • Open: Shared under TPP 1.0.
  • Open: This part was bought off the shelf. It is probably prior art. For high volume commercial use though check the legal status though (and let us know please)
  • Open: Prior art (most likely)

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

14 headphone speakers

via Trikka Headphones

Part info

  • Off the shelf headphone speakers
  • material: diverse
  • measures: ⌀ 40mm, height 8mm

Tolerance

  • Size: To work in the solutions this part was introduced with it should stay within the measures mentioned above. But this seems to be an industry standard anyway. (See also below at “buy”.)
  • Material: standard tolerance

Get the part

  • Buy: Readily available in stores. This seems to be an industry standard. You can find it in many professional headphones on the market but also easily get it as spare parts or for DIY headphone projects. Search term: “DIY headphones speaker 40mm”. The installation requires soldering though.
  • Make: No instructions available.

Introduced by

  • Designer: Lars Zimmermann via Trikkka headphones
  • Open: This part was bought off the shelf. It is probably prior art. But if you plan to make this yourself – which is pretty unlikely – and use it commercially check the legal status though.

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

15 headphone ring

via Trikka Headphones

Part info

  • ring/tube
  • material: strong (or bendable)
  • measures: diameters: inner ⌀ min 40 mm outer ⌀ max 54 mm; height: ~10mm, min 9 mm; gate: the small gate at one side is 2 mm x 2 mm.

Tolerance

  • Size: some deviation from the standard tolerance: Inner ⌀ min 40 mm outer ⌀ max 54 mm, height min 9 mm. (The current use cases do not necessarily require this part to be round – as long it has enough space to place something round with a ⌀ of 40 mm in the center. This might change though with the discovery of future use cases.)
  • Material: standard tolerance

Get the part

  • Buy: Only as local make.
  • Make: 3 ways to make this: (1) Find some fitting pipes, cut them and add the little gate with a saw. This requires some craftsmanship though. (2) You can also 3d print this easily. > STL file DOWNLOAD (3) Another way to make this is to get some strong bendable material like PP, cut out a stripe and melt it together or bolt it together to a perfect circle.

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

16 headphone ear pad

via Trikka Headphones

Part info

  • Off the shelf foam ear pads for headphones
  • material: foam
  • measures: ⌀ 70mm

Tolerance

Get the part

  • Buy: Readily available in stores, search for: “headphone earpad covers” or something similar. Here is an Ebay link that shows an off the shelf example. 
  • Make: No instructions available. We played with some ideas to make this ourselves but opted to get it ready made. If you have ideas how to make this without much effort and then more universal pls. let us know.

Introduced by

  • Designer: Lars Zimmermann via Trikkka headphones
  • Open: This part was bought off the shelf. It is probably prior art. For high volume commercial use though check the legal status though (and let us know please)

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

038.1

17 Cecilia lamp shade part

via Cecilia Lamp Shade

Part info

  • bendable sheet
  • material: bendable
  • measures: ~ 210 mm x ~ 150 mm
  • holes: Trikka grid, 4 holes ⌀ 4mm. For locations see drawing.

Tolerance

Get the part

  • Buy: Only as local make.
  • Make: This is easy to make by hand or with a laser cutter for example. Paper works. We recommend PP (Polypropylen) 0,8 mm or 0,5 mm for a more durable part.

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

18 Washer diameter 40mm

via Platform Clocks

Part info

  • Washer
  • material: strong
  • measures: outer diameter ~40mm, thickness ~16mm
  • holes: one center hole ⌀ 10mm (but it can also be slightly bigger)

Tolerance

Get the part

  • Buy: As local make, but you can get washers for M10 in stores. The holes in these off the shelf M10 washers are a bit bigger than 10mm. But they might work for your use case equally well.
  • Make: One way to make this is to use a laser cutter. → DOWNLOAD vector file here.

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

19 M4 knurled nut

via Lift Lamp

Part info

  • Off the shelf M4 knurled nut
  • material: strong

Tolerance

Get the part

  • Buy: Readily available in stores, search for: “M4 knurled nut”
  • Make: No instructions available.

Introduced by

  • Designer: Lars Zimmermann via Lift Lamp
  • Open: This part was bought off the shelf. It is probably prior art. If you intend to make this yourself though for commercial use you should check the legal status.

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

20 M4 washer 15mm

Part info

  • Off the shelf M4 washer
  • material: strong
  • measures: ⌀ 15 mm
  • holes: one center hole ⌀ 4,3 mm

Tolerance

Get the part

  • Buy: Readily available in stores, search for: “M 4 washer 15 mm”
  • Make: No instructions available.

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

info soon

21 Strap 420mm, 14 holes

Part info

  • Strap
  • material: bendable but strong
  • measures: ~ 420 mm x ~ 30 mm
  • holes: Trikka grid, 14 holes ⌀ 4 mm

Tolerance

Get the part

  • Buy: Only as local make.
  • Make: This is easy to make. We recommend PP (Polypropylen) 0,8 mm or 1 mm  for it. PP can be cut by hand but you can also use a laser cutter. For this we share laser-cut-ready files: DOWNLOAD file here

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

22 Strap 180 mm, 6 holes

  • Strap
  • material: bendable but strong
  • measures: ~ 180 mm x ~ 30 mm
  • holes: Trikka grid, 6 holes ⌀ 4 mm

Tolerance

Get the part

  • Buy: Only as local make.
  • Make: This is easy to make. We recommend PP (Polypropylen) 0,8 mm or 1 mm  for it. PP can be cut by hand but you can also use a laser cutter. For this we share laser-cut-ready files: DOWNLOAD file

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

23 Strap 2 holes (PP bracket)

  • Strap
  • material: bendable but strong
  • measures: ~ 60 mm x ~ 30 mm
  • holes: Trikka grid, 2 holes ⌀ 4 mm

Tolerance

Get the part

  • Buy: Only as local make.
  • Make: This is easy to make. We recommend PP (Polypropylen) 0,8 mm or 1 mm  for it. PP can be cut by hand but you can also use a laser cutter. For this we share laser-cut-ready files: DOWNLOAD file

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

24 Strap Hinge

  • strap
  • material: bendable but strong
  • measures: ~ 60 mm x ~ 60 mm
  • holes: Trikka grid, 4 holes ⌀ 4 mm

Tolerance

Get the part

  • Buy: Only as local make.
  • Make: This is easy to make. We recommend PP (Polypropylen) 0,8 mm or 1 mm  for it. PP can be cut by hand but you can also use a laser cutter. For this we share laser-cut-ready files: DOWNLOAD file

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

–

25 branch ⌀ ≤ 16mm, ~ 390 mm

via hanger one

Part info

  • a branch from a tree
  • material: strong (wood)
  • measures: diverse, but at least 50% should have a diameter ≤ 16mm, ~390 mm

Tolerance

Get the part

  • Buy: Readily available… outdoors | Also as local make.
  • Make: No instructions available

Introduced by

Post license & disclaimer

  • This post is shared under the Creative Commons Attribution 4.0 license.
  • Disclaimer: This part is just a concept and not fully tested. You should not assume that it works as indicated and I am not saying that it does. I disclaim any responsibility or liability for any damage caused during the construction and use of products based in whole or in part on the concept shown here. All information is provided for your use at your own risk.

26 –